Zero Modular Shellholder System
$225.00
As we have done round after round of press testing, both with the ZERO and other presses, we have known that the very best way to get consistent sizing time and again is to have contact between the shellholder and the die. This removes your ability, however, to dial in your shoulder bump – until now. With the new ZERO Modular Shellholder System you can set up your shellholder to your die and have more consistency, more repeatability, and less hassle. It’s a win-win-win.
Available in either a Zero specific mounting system or a traditional shellholder this allows you to dial in should bump with a set of 6 precision ground stainless steel inserts .002″ at a time.
The Kit comes with:
– A Base (meant for ZERO or Traditional presses, your choice)
– THREE Shellholder/Extractor tops, sized for 223 (.384″ Bolt Face), 308 (.470″ Bolt Face), Standard Magnum (.540″ Bolt Face) or similar
– SIX Precision Ground headspace inserts ranging from +.002″ to -.008″
– Aluminum Storage Block
| Weight | N/A |
|---|---|
| Dimensions | N/A |
| Style | Traditional, Zero |
77 reviews for Zero Modular Shellholder System
Related products
Stephen M. (verified owner) –
Its exacly what I wanted
Greg W. (verified owner) –
Makes sizing easier to stay precise
Josh V. (verified owner) –
These work great and are machined very well. Measured them and they are spot on 2 thou increments. You will still need to slightly over cam your dies to the shell holder and then adjust with the inserts to find your bump. I made the mistake of just running the die down to touch the shell holder. Then it dawned on me to screw down a little further. Allows for very consistent shoulder set back. Wish they made more shell holder sizes for the ARC etc family of cartridges.
Craig Arnzen (store manager) –
We plan on adding some additional claw sizes over time – so stay tuned!
Brian Garber (verified owner) –
Good product. Only feed back I have is if there was a small magnet to hold in each of the shims that would be great. This would prevent all of them from going flying when you knock this off your reloading bench.
Craig Arnzen (store manager) –
Pro tip – don’t do that…
Enjoy the kit, and thank you for your business!
Richard Drake (verified owner) –
nice
Seb F (verified owner) –
This is a big improvement over the Redding Competition Shell Holder Set. I had to purchase three and mix and match to get the differences to be CLOSE to the .002 its supposed to be. On top of the, the other shell holders referenced off the standard shell holder. So if that ever gets marred or lost and you need a new one, you could be out of spec. This on the other hand uses the same shell holder – so that measurement never changes, the only thing that does is the plate. When I first got these I took out the tube micrometer and the claimed tolerance differences were in the ten-thousands range! When put on a Redding Instant Indicator (not as sensitive but sensitive enough to measure shoulder set back), everything was within spec. So pretty much it works as advertised – which again – was no easy feat in the past. Well worth the wait.
Ty (verified owner) –
Simple, easy, worth it.
Brian (verified owner) –
Good item
Joseph Loehle (verified owner) –
Works like a charm.
kythe stillwell (verified owner) –
Awesome Precision shell holder set. Looking for to added sizes in the future.
Scott R. (verified owner) –
Love it and my Zero Press …now we need a size for the 6.5 grendel
Thomas Haberman (verified owner) –
👍
Mervyn Masumura (verified owner) –
A quality product
Bruce McGaughey (verified owner) –
Great for my OCD
Charles R. (verified owner) –
Great product with a noticeably tighter fit on brass. Run out measurements improved by 50% over Redding shell holder used prior to arrival of the ZERO.
Jim Dooley (verified owner) –
This is perfect! Instead of buying multiple sets from another company. I can use this one set across various Cartridges. Hopefully they will introduce other shell holders for 6mm Arc / 6.5 Grendel.
Peter A. (verified owner) –
Must have
Brian Smith (verified owner) –
This is what I have been waiting for as a upgrade to my Zero, makes hitting proper headspace easy. Thanks for such great products and innovation.
Paul (verified owner) –
Well made shell holders.
Gus (verified owner) –
This rocks. Took a few tries to narrow down which ring to use, but it’s cool that I have options!
Patrick Martin (verified owner) –
There is no better shell holder system on the market. Well thought out design, implemented right.
Robert (verified owner) –
Live it!
Michael May (verified owner) –
Everything you need in one place!
This system will change the way your bumping your brass. Couple this with a Zero and I get .0005 consistency in my brass. Thank you Area 419
Niklas (verified owner) –
Love this shellholder only wish that there was a nr 35 claw for my 300 Norma still have to use my old redding competition shellholders for that😅
Phil Harper (verified owner) –
This fixed my shoulder bumps on brass. This is a must
Muhammed S. (verified owner) –
Excellent quality
Jacob J. (verified owner) –
Have not used this yet but will soon but everything fits together nicely and looks great.
Corey (verified owner) –
Again not used yet but percise!
Scott H. (verified owner) –
This set is a big step up from other shell holder sets on the market. Love the ability to use over a range of cartridges with differing bases. Would like to see an expanded storage base for the flat (Zero bullet seater) plate and additional cartridge claws
Tony Todd (verified owner) –
Works great and looks great to
Craig (verified owner) –
Great
John G. (verified owner) –
Was not sure about doing this, but very pleased with system. Everything works exactly as stated. Super consistent results so far.
Toma (verified owner) –
A+
Anonymous (verified owner) –
Best she’ll holder system available
Dave Parrish (verified owner) –
I think the system is of good design in engineering, fit and finish. I would havevrated the set as a 5 had the magnet not fallen out of the tool with first use without being dropped or misused.
Don Dory (verified owner) –
The good news is that it will accommodate my 6.5×55 brass. the “shims” track very precisely the movement needed. The only issue is for chambers that are not SAMMI. Then your die is still off the shell holder until the custom die comes in. The great news is that the zero press is extremely repeatable so my headspace didn’t change more than 0.0005 which could be tolerances in annealing.
Michael R. (verified owner) –
Great
Larry Hamblin (verified owner) –
Awesome
BAOQING ZHU (verified owner) –
Good
Brandon H –
Don’t buy if you have whidden dies. Your bass will be way over sized.
Wesley C. (verified owner) –
Excellent product
Ronald B. (verified owner) –
Top quality
William Newbold (verified owner) –
Loved it, but when are you coming out with one that will work with 338 Lapua
Sandy S. (verified owner) –
The cats meow!
Richard Dickens (verified owner) –
Still experimenting but excellent so far
Tony B. (verified owner) –
Well designed and I’m excited to try it out.
William Simpson (verified owner) –
Terrific product.
Lawson Smith (verified owner) –
Still getting accustomed to using it. Had problems loading my 223 loads. Shoulder set back was not coming out right. Then I realized that I was shooting the shells in a 5.56 and loading them on a set of .223 dies. My bad!
Jan Cremers (verified owner) –
Super quality!! Works great!
Tim W –
would absolutely purchase , If a set was made for 375 cheytac and 416/50BMG brass – actually would buy both, as the Area 419 bling is the best bling!!!
Samuel (verified owner) –
Well thought out items and very well made.
Arron Hamilton (verified owner) –
Hoping to zero in & be more precise on my shoulder bump in my sizing on my zero press
Art Bogden (verified owner) –
I would pay a lot more for this product.
John (verified owner) –
Need shoe for larger calibers. 375 CheyTac
Berchman Ortego (verified owner) –
Love them. Great idea and easy to use.
ionut D. (verified owner) –
The perfect complément for my Zero press!
Anonymous (verified owner) –
Made great as expected. Would like to see in mounted on press .
steve-9879 –
please make a Cheytac / enABELR shell holder, it’s the only thing missing for this to be truly perfect
Todd Van Dyke (verified owner) –
Very well thought out. Worked as described. Fit my Zero press exactly!
John (verified owner) –
This shellholder set and annealing each firing totality takes the guess work out of shoulder bumping. The quality speaks for itself. Very pleased.
Ernie Waldner (verified owner) –
haven’t tried it since the dies are on back order
Mihai Boc (verified owner) –
Another quality item from the team. Would be nice to be able to mount this to the press
James Chisom (verified owner) –
Big addition to my loading ability
Doug Evancic (verified owner) –
Awesome product very pleased.
Lance H. (verified owner) –
Excellent quality. Another wat Are419 provides for exact control of your reloading process.
William M. (verified owner) –
Wish they fit 300 Norma magnum… Still incredible for most everything else.
neale white (verified owner) –
Great quality
Tevis Smith (verified owner) –
I like knowing everything is flat a square
Svein Soermo (verified owner) –
Same as the rest – gold standard!
Sandy S. (verified owner) –
I purchased this for my std. single stage and had to reorder for the New Zero. So now I’m set no matter what comes my way.
Dan W. (verified owner) –
I own a number of Area 419 products. This is consistent with the ultra high quality of all they produce.
They set the bar high and exceed the mark!
Jonathan Macari (verified owner) –
Love this system for sizing brass
Douglas M. (verified owner) –
These are like sliced bread. Once you use this, you will wonder why you waited so long.
Michael Langlois (verified owner) –
Unbelievably nice and precise; like everything else form Area 419.
Joseph Greer (verified owner) –
Very high quality and easy to use
Peter Russell (verified owner) –
Always prompt service and great quality, keep it up !
Micah M. (verified owner) –
Haven’t had a chance to use it much but it’s nicely made.